Bar,toolholder,drills,taps,kennametal,sandvik,iscar,seco,

Inserts Kennametal Sandvik

September 7th, 2011 admin No comments

China’s Super

Coating Diamond coating is a new

Tools Coating materials. It uses Low Chemical vapor deposition Technology Hard alloy The growth of a layer of substrate formed by the polycrystalline diamond film, with its processing of silicon

Aluminum And Copper Alloy Etc. Non-ferrous metals , Glass fiber Etc. Project Materials and carbide materials, tool life is ordinary carbide cutting tools 50 ~ 100 times. Diamond coating with a number of diamond synthesis technology, the most common is the hot wire method, microwave

Plasma France and the DC plasma jet. By improving the adhesion of coating methods and coating, diamond coated tools have been produced and has been applied in industry.

Recent years, the United States, Japan and Sweden have already introduced a diamond coated taps,

Reamer , Mills And for processing Print PCB Holes on the diamond coated carbide

Drill And a variety of indexable inserts, such as the Swedish company Sandvik

CD Kennametal Inc. in 1810 and the United States and other trademark products KCD25. U.S. Turchan developed a new laser plasma deposition process of diamond, diamond deposition method has been applied, because the plasma field surrounding the tool, tool on the coating, the deposition rate faster than the conventional CVD method 1000 times. This law into the diamond coating and the substrate between a real

Metallurgy Combination of high strength coating to prevent coating to peel, crack and crack. CemeCon company has a unique CVD diamond coating technology, established in 2000

Production Line To diamond coating technology to achieve the level of industrial production, its high technology can be mass produced diamond coatings.

Diamond coating on some of the materials (Al, Ti and

Composite materials ) Machining side Mask Has obvious advantages. By low pressure vapor deposition diamond coating, the microstructure and there are quite different than natural diamond. Nineties, often with active hydrogen in the presence of low-pressure vapor deposition of DLC, the coating contains a lot of hydrogen. Excess hydrogen will reduce the coating adhesion strength and hardness, internal stress increases. DLC in hydrogen at high temperatures will slowly released, causing instability in coating work. The DLC is not hydrogen than the hydrogen in the DLC hardness is high and homogeneous deposition can be large area, low cost, surface roughness etc., has become a research hotspot in recent years, DLC coating. U.S. scientists AAVoevodin superhard DLC coatings deposited proposed structural design for the Ti-TiC-DLC gradient coating changes, so that the hardness from the soft steel substrate is gradually raised to the surface of the DLC superhard coatings. Such composite coatings to maintain the high hardness and low friction coefficient, but also reduce the brittleness, improve capacity, adhesion and wear resistance. Sumitomo Corporation of Japan introduced a diamond coated cemented carbide inserts on the DL1000 DLC coatings for cutting aluminum and non-ferrous metals, anti-bonding, can reduce the roughness of machined surface.

After years of research shows: As the internal stress of diamond coating of high thermal stability and with poor

Black Metal Effect between the catalyst to the change in SP2 SP3 structural defects to determine that it is currently only used in processing non-ferrous metals, which limits its further application processing machine. But in recent years, research has shown that the structure with SP2-based diamond coating (also known as graphite coating) hardness up to 20 ~ 40GPa, does not exist and black metal from the catalytic effect of the problem, the friction coefficient is low there are good anti-wet, cutting the coolant can also be used for dry cutting, the life expectancy has doubled compared with no increase in coating knife, can be processed

Steel Materials, thus causing the coating companies, tool manufacturers of great interest. Over time, this new diamond coated cutting areas will be widely used.

2. Cubic boron nitride (CBN) coatings

CBN is the second synthetic diamond that appears after another hard material, which in addition has many excellent diamond of similar physical and chemical properties (such as high hardness, second only to diamond, high wear resistance, low friction coefficient, low thermal expansion coefficient, etc.), the Diamond also has some superior features. CBN for iron, steel and

Oxidation Chemically inert environment, the formation of a thin layer in the oxidation of boron oxide, the oxide coating provides chemical stability, so it hard in the processing of iron material, gray cast iron heat resistance is also very good, at a very high cutting temperatures can cut heat-resistant steel, hardened steel,

Titanium

And so on, and to cut the chill roll hardness, as well as carburized material very serious tool wear and other difficult materials silicon aluminum alloy.

About the Author

I am China Manufacturers writer, reports some information about purse key finders , round purse.

Sandvik CoroMill 345 and CoroMill 316 Demo in Steel